Round anti-slip self-adhesive furniture glides keep round-legged furniture from sliding on smooth, hard floors. NR+CR rubber grips without scratching or staining. EHBF acrylic adhesive bonds to metal, plastic, chrome, and wood. No drilling, no tools.
Not sure what size? See the size chart ↓
📦 Sold in packs of 4 — quantity adjustable at checkout
Metal, plastic, and hollow tube legs that slide on smooth floors need grip, not glide. But they can’t accept a nail-on rivet either. Round anti-slip self-adhesive furniture glides solve both problems: NR+CR (natural rubber + chloroprene rubber) grips the floor without scratching, staining, or marking, while EHBF acrylic foam adhesive bonds to any clean, smooth round surface.
Non-slip chair leg protectors that hold position on hardwood, tile, laminate, vinyl, and stone. Peel the backing, center the glide, Press firmly for 30 seconds. Allow 48 hours for full adhesive cure before heavy use. The EHBF adhesive builds bond strength progressively over 24 hours.
Round anti-slip self-adhesive furniture glides come in from Ø 23 mm to Ø 75 mm. Anti-slip peel-and-stick floor protectors for wood, metal, plastic, chrome, powder-coated steel, and composite legs. For any round leg material. Sold in packs of 4.
Five diameters cover every standard round furniture leg. The glide should be slightly smaller than the leg diameter so it stays hidden beneath the leg edge.
If your measurement lands on a boundary, choose the smaller round anti-slip self-adhesive furniture glide.
For legs Ø 23–27 mmSide chairs, lightweight accent furniture
For legs Ø 28–37 mmDining chairs, kitchen chairs, bar stools
For legs Ø 38–49 mmAccent chairs, heavier seating, counter stools
For legs Ø 50–74 mmAccent tables, display furniture, and equipment
For legs Ø 75 mm and aboveLarge tables, heavy commercial furniture
For solid wood legs, round anti-slip nail-on furniture glides use a tubular rivet instead of adhesive. For smooth gliding instead of grip, round self-adhesive furniture glides use PA6 fiber. For bulk orders, visit Business Solutions.
Measure the leg base to find the right size. The most common mistake is guessing the leg size.
A glide that’s too large overhangs and peels. A glide that’s too small leaves the leg perimeter in direct contact with the floor. With measuring takes 30 seconds.
Lay the piece on its side or turn it upside down. You need full access to the flat bottom face of each leg where the round anti-slip self-adhesive furniture glide will bond.
Use a ruler or calipers across the widest point of the leg base. For tapered legs, measure at the very bottom. The base is the only measurement that matters.
Select the round anti-slip self-adhesive furniture glide whose range includes your measurement. If you’re on a boundary, go with the smaller size so the glide stays inside the leg edge.
No tools. No drilling. No hardware. Every round anti-slip self-adhesive furniture glide comes with EHBF (red) adhesive pre-applied.
Peel the backing, center the glide, press firmly. The whole job takes less time than reading this section.
The NR+CR rubber compound in round anti-slip self-adhesive furniture glides is not commodity rubber. Natural rubber (NR) provides high-friction grip. Chloroprene rubber (CR) adds UV resistance, chemical stability, and prevents the staining that cheap rubber causes on light-colored hardwood.
NR+CR rubber has a high coefficient of friction against smooth, hard surfaces. The rubber deforms microscopically into the floor’s surface texture and resists lateral movement.
The grip is proportional to weight: heavier furniture grips harder. This makes round anti-slip self-adhesive furniture glides especially effective under heavy items like bar stools, accent tables, and display furniture.
The CR component prevents the chemical staining that pure natural rubber causes on polyurethane-finished hardwood, light-colored vinyl, and sealed stone. NR+CR will not yellow, harden, or crack under normal indoor conditions.
It won’t transfer color to the floor. And unlike silicone-based anti-slip products, NR+CR doesn’t leave residue when the glide is removed. Non-slip floor protectors that grip without damaging the finish.
NR+CR rubber is chemically stable and non-staining on all sealed floor finishes. The National Wood Flooring Association (NWFA) recommends furniture protectors on every leg as a primary hardwood maintenance step.
Round anti-slip self-adhesive furniture glides meet that standard while adding controlled grip. Non-slip hardwood floor protectors that are safe for every surface listed below.
Furniture on boats, yachts, and cruise ships faces constant lateral force from wave motion, engine vibration, and course changes. Round anti-slip self-adhesive furniture glides are built for exactly this environment.
The chloroprene rubber (CR) component resists salt spray, UV exposure from cabin windows and open decks, and the constant humidity cycling that degrades natural rubber. The high-friction NR+CR surface holds furniture in position against wave-induced lateral forces on sealed teak, fiberglass, or cabin flooring.
Self-adhesive mounting is ideal for marine furniture on metal and composite frames that cannot accept a rivet.
EHBF acrylic foam adhesive resists the constant vibration that loosens commodity adhesives. The closed-cell foam conforms to minor surface irregularities on marine-grade leg materials.
NR+CR rubber is non-staining on sealed teak, marine-grade vinyl, fiberglass decking, and polished cabin floors. No marks, no discoloration, no residue. Anti-slip furniture glides for marine environments where furniture stability is a safety requirement.
Three components work together in every round anti-slip self-adhesive furniture glide. One grips your floor. One bonds the glide to your furniture leg. One sits between them and distributes the load.
Blended rubber compound formulated for sustained floor contact. Natural rubber provides a high-friction grip proportional to furniture weight. Chloroprene rubber adds UV stability, chemical resistance, and prevents staining on polyurethane finishes.
Unlike cheap rubber products that stain and degrade, NR+CR maintains its grip and chemical stability long-term without discoloring the floor.
EHBF is a closed-cell acrylic foam tape that bonds the ABS platform to any smooth leg surface. Unlike commodity double-sided tape that peels under lateral stress, EHBF builds bond strength progressively and resists creep.
The closed-cell foam conforms to minor surface irregularities and provides vibration damping.
The rigid circular disc between the NR+CR surface and the EHBF adhesive layer distributes compression load evenly across the full glide surface. Prevents the rubber from deforming under heavy sustained weight, maintaining a consistent grip across the entire contact area.
If round-legged furniture on metal or plastic frames slides when it shouldn’t, and a nail-on rivet isn’t possible, here’s how round anti-slip self-adhesive furniture glides compare.
Generic rubber caps use unformulated natural rubber that stains polyurethane finishes, yellows under UV, and hardens over time until the grip disappears.
Round anti-slip self-adhesive furniture glides use NR+CR blended rubber that won’t stain, won’t yellow, and maintains a consistent grip long-term. The ABS platform prevents the deformation that causes cheap caps to lose their shape.
Felt pads are designed to reduce friction, the opposite of what anti-slip furniture needs. Felt compresses flat under load, absorbs moisture, traps grit, and provides zero grip.
NR+CR rubber provides high-friction grip that increases proportionally with furniture weight. The EHBF adhesive holds long-term. No compression, no moisture absorption, no failure.
Same NR+CR surface, same ABS platform. The difference is mounting. Round anti-slip nail-on furniture glides use a tubular rivet for solid wood legs, providing the strongest possible bond.
Round anti-slip self-adhesive furniture glides use EHBF (red) adhesive for metal, plastic, chrome, hollow tube, or any leg where a rivet isn’t possible. Choose based on leg material.
Same ABS platform, same adhesive, same sizes. Opposite function. Round self-adhesive furniture glides use PA6 for furniture that needs to move freely. Round anti-slip self-adhesive furniture glides use NR+CR for furniture that must stay put.
Choose based on the job: movement or grip.
Round anti-slip self-adhesive furniture glides are built on the same ABS platform and adhesive system used across the self-adhesive line. The only difference is the contact surface, which determines whether furniture holds position or moves freely.
High-friction NR+CR rubber for round-legged furniture that must stay put. Bar stools, accent tables, display furniture, and marine seating on metal, plastic, or hollow tube legs. These are the non-slip self-adhesive furniture glides you are viewing now.
Low-friction PA6 fiber for round-legged furniture that repositions regularly. Dining chairs, kitchen chairs, desk seating. Anything that should move silently.
Both variants use the same ABS platform and acrylic foam adhesive. Only the floor-contact surface differs: NR+CR for grip, PA6 for movement.
The glide shape must match the leg cross-section. All three anti-slip shapes use the same NR+CR surface, ABS platform, and acrylic foam adhesive.
For circular, turned, tapered, and cylindrical legs. from Ø 23 mm to Ø 75 mm.
For equal-sided square legs. Full corner-to-corner grip. from 23 × 23 mm to 75 × 75 mm.
For rectangular legs with unequal sides. 33 × 19 mm.
Any situation where round non-wood legs meet smooth, hard flooring, and the furniture must not move. These are the professional-grade non-slip peel-and-stick floor protectors for metal, plastic, and composite round-legged furniture when cheap rubber stains, silicone leaves residue, and felt provides zero grip.
Chrome and metal bar stools that slide across kitchen tile are the single most common residential application. Accent tables that drift on polished hardwood. Metal plant stands, display pedestals, and any round-legged metal or plastic furniture that shifts when it shouldn’t.
Non-slip self-adhesive chair leg protectors that put grip within reach of every homeowner.
Restaurant bar stools on polished concrete. Hotel lobby accent tables. Retail display fixtures and showroom furniture. Gallery and museum display stands. Healthcare waiting room furniture.
Yacht salons, cruise ship dining rooms, and boat cabins where wave motion and engine vibration push unprotected furniture across sealed decking. Available in bulk for venue and vessel fit-outs. For commercial pricing, visit Business Solutions.
Identical NR+CR surface and ABS platform. ZnFe tubular rivet instead of EHBF adhesive, for solid wood legs where maximum mechanical hold is preferred.
Same ABS platform and acrylic adhesive. PA6 surface instead of NR+CR, for round-legged furniture that needs to move freely.
| Specification | Details |
|---|---|
Product Type |
Anti-Slip Self-Adhesive Furniture Glides |
Shape |
Round |
Surface Material |
NR+CR Natural Rubber + Chloroprene Rubber |
Platform Material |
ABS Acrylonitrile Butadiene Styrene |
Adhesive |
EHBF Extra High Bond Foam Acrylic Tape |
Leg Compatibility |
Solid wood, metal, and plastic legs |
Floor Compatibility |
Smooth, hard floors |
Sizes Available |
Ø 23 mm – Ø 75 mm (0.91″ – 2.95″) |
Pack Quantity |
Sold in multiples of 4 |
Color |
Black |
Installation |
Press firmly for 30 seconds. Allow 48 hours before heavy use |
Indoor/Outdoor Use |
Indoor | Covered Outdoor | Marine |
| L × W (Size) | Compatible Leg Size | H (Height) | Weight |
|---|---|---|---|
23 × 23 mm (0.91″ × 0.91″) |
23 – 27 mm (0.91 – 1.06″) |
12 mm (0.47”) |
3.5 g |
28 × 28 mm (1.10″ × 1.10″) |
28 – 37 mm (1.10 – 1.46″) |
12 mm (0.47”) |
4.6 g |
38 × 38 mm (1.50″ × 1.50″) |
38 – 49 mm (1.50 – 1.93″) |
12 mm (0.47”) |
7.0 g |
50 × 50 mm (1.97″ × 1.97″) |
50 – 74 mm (1.97 – 2.91″) |
12 mm (0.47”) |
17.2 g |
75 × 75 mm (2.95″ × 2.95″) |
75 mm and above (2.95″+) |
12 mm (0.47”) |
38 g |
NR+CR is a blend of natural rubber (NR) and chloroprene rubber (CR). Natural rubber provides a high-friction grip that increases with furniture weight. Chloroprene rubber adds UV resistance, chemical stability, and prevents the staining that pure natural rubber causes on polyurethane-finished hardwood, light-colored vinyl, and sealed stone. The combination grips without marking, yellowing, or leaving residue on any sealed floor finish.
Both use the same ABS platform, the same adhesive, and the same five sizes. The difference is the floor-contact surface. Round self-adhesive furniture glides (Smooth Glide) use low-friction PA6 fiber for furniture that needs to move freely, like dining chairs. Round anti-slip self-adhesive furniture glides use NR+CR rubber for furniture that must stay put, like bar stools and accent tables.
Yes. The chloroprene rubber (CR) in the NR+CR blend resists salt spray, UV exposure, and the constant humidity cycling found in marine environments. EHBF acrylic foam adhesive resists constant vibration that loosens commodity adhesives. NR+CR is non-staining on sealed teak, marine-grade vinyl, and fiberglass decking. Self-adhesive mounting is ideal for marine furniture on metal and composite frames that cannot accept a rivet.
Generic rubber caps use unformulated natural rubber that chemically reacts with polyurethane floor finishes, leaving permanent dark stains on light-colored hardwood and vinyl. NR+CR blends natural rubber with chloroprene rubber (CR), which blocks that chemical reaction entirely. NR+CR also resists UV yellowing, hardening, and cracking. The grip stays consistent long-term instead of degrading until the cap becomes useless.
EHBF acrylic foam adhesive bonds to wood, steel, aluminum, chrome, stainless steel, plastic, powder-coated metal, and composite materials. On chrome legs, clean thoroughly for the strongest bond. On plastic legs with low surface tension, test adhesion on a small area first. The adhesive builds bond strength progressively over 24 hours under the furniture’s own weight.
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet