Square self-adhesive furniture glides protect smooth, hard floors from scratches. Corner-to-corner PA6 coverage for square legs on any material. EHBF acrylic adhesive bonds to metal, plastic, chrome, and wood. No drilling, no tools.
Not sure what size? See the size chart ↓
📦 Sold in packs of 4 — quantity adjustable at checkout
Square-legged metal, plastic, and hollow tube furniture needs corner-to-corner floor protection. But these legs can’t accept a nail-on rivet. And a round self-adhesive glide on a square leg leaves all four corners exposed to scratch the floor.
Square self-adhesive furniture glides solve both problems: PA6 needle-punched fiber covers the full square footprint while EHBF acrylic adhesive bonds to any clean, smooth square surface. Silent, scratch-free movement on hardwood, tile, laminate, vinyl, and stone.
Peel the backing, align the corners, Press firmly for 30 seconds. Allow 48 hours for full adhesive cure before heavy use. The EHBF adhesive builds bond strength progressively over 24 hours under the furniture’s own weight.
Square self-adhesive furniture glides are available in from 23 × 23 mm to 75 × 75 mm. Peel-and-stick chair leg protectors for square legs on every smooth, hard floor. For any square leg material. Sold in multiples of 4.
Five square dimensions cover every standard square furniture leg. The glide should be slightly smaller than the leg so it sits inside the footprint.
Corner-to-corner PA6 coverage is the entire point. If your measurement lands on a boundary, choose the smaller square self-adhesive furniture glide.
For legs 23–27 mmSide chairs, lightweight accent furniture
For legs 28–37 mmParsons chairs, dining chairs, desk seating
For legs 38–49 mmAccent tables, heavier seating, counter stools
For legs 50–74 mmDisplay furniture, heavy accent tables
For legs 75 mm and aboveLarge tables, heavy commercial furniture
For solid wood legs, square nail-on furniture glides use a tubular rivet instead of adhesive. For anti-slip grip, square anti-slip self-adhesive furniture glides use NR+CR rubber. For bulk orders, visit Business Solutions.
Measure the leg base to find the right size. Square legs look simple, but tapered designs are wider at the top and narrower at the bottom.
The only measurement that matters is the flat face at the very bottom of the leg. With measuring takes 30 seconds.
Lay the piece on its side or turn it upside down. You need full access to the flat bottom face of each leg where the square self-adhesive furniture glide will bond.
Use a ruler across one edge of the flat base, in millimeters. Both sides should be equal on a true square leg. If the sides are noticeably different, the leg is rectangular. Use rectangular self-adhesive furniture glides instead.
Select the square self-adhesive furniture glide whose range includes your measurement. If you’re on a boundary, go with the smaller size so the glide stays inside the leg footprint.
No tools. No drilling. No hardware. Every square self-adhesive furniture glide comes with EHBF adhesive pre-applied.
Peel the backing, align the corners, press firmly. The whole job takes less time than reading this section.
PA6 is chemically inert and leaves no marks, scuffs, or residue on any sealed floor finish. The National Wood Flooring Association (NWFA) recommends furniture protectors on every leg as a primary hardwood maintenance step.
Square self-adhesive furniture glides meet that standard across every smooth, hard floor type. Corner-to-corner hardwood floor protectors that cover every square millimeter.
Three components work together in every square self-adhesive furniture glide. One touches your floor. One bonds the glide to your furniture leg. One sits between them and distributes the load.
PA6 fibers are forced through the base material by thousands of barbed needles during manufacturing. Each fiber is mechanically interlocked with its neighbors. No glue holding it together. No layers to separate.
The result is a dense, low-friction surface (1,450 g/m² pile density) covering the full square footprint, corners included. Unlike cheap felt pads that compress and trap grit, PA6 deflects debris and maintains its smooth surface through extended daily use.
EHBF is a double-sided self-adhesive fiberglass mesh tape that bonds the ABS platform to any smooth leg surface. Unlike commodity double-sided tape that peels under lateral stress, EHBF builds bond strength progressively under the furniture’s own weight.
The fiberglass mesh provides shear resistance that prevents the creep and stretch that peel cheap adhesive off furniture legs.
The rigid square disc between the PA6 surface and the EHBF adhesive distributes compression load evenly across the full square footprint, including all four corners. No concentrated stress at any edge, no curling under asymmetric weight.
Most off-the-shelf peel-and-stick floor protectors are round. If you’ve been sticking felt pads on square legs, you’ve been leaving all four corners unprotected. Here’s how square self-adhesive furniture glides compare.
A round glide inscribed inside a square leg leaves four exposed corners. The corners concentrate the most pressure on the floor and scratch first.
Square self-adhesive furniture glides cover the full footprint, edge to edge, corner to corner. These are the square floor protectors that solve the corner problem completely.
Felt compresses flat under load, absorbs moisture from floor cleaning, and traps abrasive grit. On square legs, felt compresses fastest at the corners where pressure concentrates, leaving the highest-stress points unprotected first.
PA6 needle-punched fiber can’t compress flat, doesn’t absorb moisture, and deflects debris instead of trapping it. EHBF fiberglass mesh adhesive resists the creep that peels cheap felt off furniture legs.
Same PA6 surface, same ABS platform. The difference is the attachment method. Square nail-on furniture glides use a tubular rivet for solid wood, providing the strongest possible mechanical bond.
Square self-adhesive furniture glides use EHBF adhesive for metal, plastic, chrome, hollow tube, or any leg where a rivet isn’t possible. Choose based on leg material.
Same ABS platform, same adhesive, same sizes. Opposite function. Square anti-slip self-adhesive furniture glides use NR+CR rubber for furniture that must stay put. Square self-adhesive furniture glides use PA6 for furniture that needs to move freely. Choose based on the job: movement or grip.
Square self-adhesive furniture glides share the same ABS platform and adhesive as the anti-slip range. The only difference is the contact surface, which determines whether furniture moves freely or holds position.
Low-friction PA6 fiber for square-legged furniture that repositions regularly. Parsons chairs, dining tables, kitchen seating, and desks on metal, plastic, or hollow tube legs. These are the corner-to-corner self-adhesive chair glides you’re viewing now.
Controlled grip for square-legged furniture that must stay put. Media consoles, sideboards, display furniture on metal, plastic, or hollow tube legs. Anywhere sliding is a problem or a safety concern.
Both variants use the same ABS platform and acrylic adhesive. Only the floor-contact surface differs: PA6 for movement, NR+CR for grip.
The glide shape must match the leg cross-section. All three Smooth Glide shapes use the same PA6 surface, ABS platform, and acrylic adhesive.
For circular, turned, tapered, and cylindrical legs. from Ø 23 mm to Ø 75 mm.
For equal-sided square legs. Full corner-to-corner PA6 coverage. from 23 × 23 mm to 75 × 75 mm.
For rectangular legs with unequal sides. Mid-century and Scandinavian furniture. 33 × 19 mm.
Any situation where square non-wood legs meet smooth, hard flooring, and the furniture needs to move freely. These are the professional-grade peel-and-stick furniture floor protectors for Parsons-style and straight-leg furniture on metal, plastic, and composite frames when felt pads fail, rubber caps drag, and nail-on rivets aren’t possible.
Metal Parsons dining chairs on hardwood are the single most common residential application. Chrome accent tables and side tables on polished floors. Metal media consoles and TV stands that need to slide when repositioned.
Any square-legged metal or plastic furniture that needs smooth, scratch-free movement. Self-adhesive chair leg protectors that put corner-to-corner PA6 protection within reach of every homeowner.
Restaurant dining chairs on metal frames. Hotel lobby furniture. Office seating and conference tables on steel bases. Retail display fixtures. Healthcare waiting room furniture. Event venue seating.
Available in bulk for venue fit-outs. For commercial pricing, visit Business Solutions.
Identical PA6 surface and ABS platform. ZnFe tubular rivet instead of EHBF adhesive, for solid wood legs where maximum mechanical hold is preferred.
Same ABS platform and acrylic adhesive. NR+CR rubber surface instead of PA6, for square-legged furniture that must hold position on smooth, hard floors.
| Specification | Details |
|---|---|
Product Type |
Self-Adhesive Furniture Glides |
Shape |
Square |
Surface Material |
PA6 Needle-Punched Polyamide 6 |
Platform Material |
ABS Acrylonitrile Butadiene Styrene |
Adhesive |
EHBF Extra High Bond Foam Acrylic Tape |
Pile Density |
1,450 g/m² |
Leg Compatibility |
Solid wood, metal, and plastic legs |
Floor Compatibility |
Smooth, hard floors |
Sizes Available |
23 × 23 mm – 75 × 75 mm (0.91″ × 0.91″ – 2.95″ × 2.95″) |
Pack Quantity |
Sold in multiples of 4 |
Color |
Black |
Installation |
Press firmly for 30 seconds. Allow 48 hours before heavy use |
Indoor/Outdoor Use |
Indoor | Covered Outdoor |
| L × W (Size) | Compatible Leg Size | H (Height) | Weight |
|---|---|---|---|
23 × 23 mm (0.91″ × 0.91″) |
23 – 27 mm (0.91 – 1.06″) |
12 mm (0.47") |
3.2 g |
28 × 28 mm (1.10″ × 1.10″) |
28 – 37 mm (1.10 – 1.46″) |
12 mm (0.47") |
4.29 g |
38 × 38 mm (1.50″ × 1.50″) |
38 – 49 mm (1.50 – 1.93″) |
12 mm (0.47") |
6.5 g |
50 × 50 mm (1.97″ × 1.97″) |
50 – 74 mm (1.97 – 2.91″) |
12 mm (0.47") |
16.3 g |
75 × 75 mm (2.95″ × 2.95″) |
75 mm and above (2.95″+) |
12 mm (0.47") |
36 g |
A round glide inscribed inside a square leg leaves all four corners exposed. Corners are the highest-pressure contact points on any square furniture leg, and they scratch the floor first when the piece moves. Square self-adhesive furniture glides match the leg cross-section corner to corner, so every edge is covered by PA6 fiber and no bare leg contacts the floor.
EHBF acrylic adhesive bonds to wood, steel, aluminum, chrome, stainless steel, plastic, powder-coated metal, and composite materials. On chrome legs, clean thoroughly before application for the strongest bond. On plastic legs with low surface tension, test adhesion on a small area first. The adhesive builds bond strength progressively over 24 hours under the furniture’s own weight.
Both use the same PA6 surface and ABS platform. The difference is the attachment method. Square nail-on furniture glides use a ZnFe tubular rivet for solid wood legs, providing the strongest possible mechanical bond. Square self-adhesive furniture glides use EHBF acrylic adhesive for metal, plastic, chrome, hollow tube, or any leg where a rivet isn’t possible. Choose based on leg material.
Both use the same ABS platform and acrylic adhesive. The difference is the floor-contact surface. Square self-adhesive furniture glides (Smooth Glide) use low-friction PA6 fiber for furniture that needs to move freely, like Parsons dining chairs. Square anti-slip self-adhesive furniture glides use NR+CR rubber for furniture that must stay put, like media consoles. Choose based on the job: movement or grip.
Yes. PA6 is chemically inert and non-staining on all sealed floor finishes, including LVP, LVT, and sheet vinyl. The National Wood Flooring Association (NWFA) recommends furniture protectors on every leg as a primary maintenance step. PA6 will not discolor, mark, or leave residue on any sealed smooth, hard floor. The full corner-to-corner coverage ensures no bare leg contacts the vinyl surface.
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet