Round Non-Slip Self-Adhesive Furniture Glides

Measure the leg base to find the right size. The most common mistake is guessing the leg size.

A glide that's too large overhangs and peels. A glide that's too small leaves the leg perimeter in direct contact with the floor. With measuring takes 30 seconds.

Step 1: Flip or tilt the furniture

Lay the piece on its side or turn it upside down. You need full access to the flat bottom face of each leg where the round non-slip self-adhesive furniture glide will bond.

Step 2: Measure the diameter

Use a ruler or calipers across the widest point of the leg base. For tapered legs, measure at the very bottom. The base is the only measurement that matters.

Step 3: Match to the size chart

Select the round non-slip self-adhesive furniture glide whose range includes your measurement. If you're on a boundary, go with the smaller size so the glide stays inside the leg edge.

Tapered legs: always measure at the very bottom. A tapered leg that measures Ø 1-9/16" (40 mm) at mid-height but Ø 1-5/16" (33 mm) at the base needs the Ø 1-1/8" (28 mm) glide, not the Ø 1-1/2" (38 mm).

No tools. No drilling. No hardware. Every round non-slip self-adhesive furniture glide comes with extra-high-bond acrylic foam adhesive pre-applied.

Peel the backing, center the glide, press firmly. The whole job takes less time than reading this section.

What you need

• 70% isopropyl alcohol and a lint-free cloth
• Access to the bottom of each furniture leg
• That's it. No tools, no drill, no screws

Installation steps

1. Wipe the bottom of the leg with isopropyl alcohol. Old wax, dust, and adhesive residue prevent a strong bond. Clean surface = strong bond.
2. Peel the backing from the round non-slip self-adhesive furniture glide to expose the extra-high-bond acrylic foam adhesive. Don't touch the exposed adhesive.
3. Center the glide on the leg and press firmly. Full contact, no air pockets, no lifted edges.
4. Set the furniture back down. The weight helps. The extra-high-bond acrylic foam adhesive builds bond strength progressively over 48 hours. The NR+CR surface grips immediately, but the adhesive-to-leg bond strengthens over time.

Surface prep for different materials: on chrome legs, clean thoroughly. Chrome provides excellent adhesion for extra-high-bond acrylic foam adhesive. On powder-coated metal, ensure the finish is fully cured. On plastic legs, test adhesion on a small area first. Some low-surface-tension plastics may need an adhesion promoter.Removal: twist the round non-slip self-adhesive furniture glide while pulling gently to break the adhesive bond. Scrape all old adhesive from the leg. Clean with isopropyl alcohol and install a fresh glide.

The NR+CR rubber compound in round non-slip self-adhesive furniture glides isn't commodity rubber. Natural rubber (NR) provides high-friction grip. Chloroprene rubber (CR) adds UV resistance, chemical stability, and prevents the staining that cheap rubber causes on light-colored hardwood.

How the grip works

NR+CR rubber has a high coefficient of friction against smooth, hard surfaces. The rubber deforms microscopically into the floor's surface texture and resists lateral movement.

The grip is proportional to weight: heavier furniture grips harder. This makes round non-slip self-adhesive furniture glides especially effective under heavy items like bar stools, accent tables, and display furniture.

What NR+CR won't do

The CR component prevents the chemical staining that pure natural rubber causes on polyurethane-finished hardwood, light-colored vinyl, and sealed stone. NR+CR won't yellow, harden, or crack under normal indoor conditions.

It won't transfer color to the floor. And unlike silicone-based non-slip products, NR+CR doesn't leave residue when the glide is removed. Non-slip floor protectors that grip without damaging the finish.

✓ Use these glides on

• Metal bar stools and counter stools that slide on tile or hardwood
• Chrome and brushed steel accent tables that drift on polished floors
• Plastic and composite furniture that must hold its position
• Solid wood legs where adhesive is preferred over a rivet
• Wooden legs where you prefer adhesive over a rivet and need grip
• Marine furniture on boats, yachts, and cruise ships
• Any round-legged furniture on smooth, hard floors that must not move

✗ Not the right product for

• Furniture that needs to move freely: use round self-adhesive furniture glides (Smooth Glide)
• Solid wood legs where a rivet is preferred: use round non-slip nail-on furniture glides
• Square legs: use square non-slip self-adhesive furniture glides
• Rectangular legs: use rectangular non-slip self-adhesive furniture glides
• Carpet or rugs: use round self-adhesive furniture slides for carpet
• Dining chairs that need to slide in and out: Smooth Glide PA6 is the right choice, not non-slip

Smooth, hard floor compatibility

NR+CR rubber is chemically stable and non-staining on all sealed floor finishes. The National Wood Flooring Association (NWFA) recommends furniture protectors on every leg as a primary hardwood maintenance step.

Round non-slip self-adhesive furniture glides meet that standard while adding controlled grip. Non-slip hardwood floor protectors that are safe for every surface listed below.

Hardwood: solid and engineered, all speciesParquet, bamboo, reclaimed woodLaminate: all types and AC ratingsLuxury vinyl: LVP, LVT, sheet vinylCeramic and porcelain tileNatural stone: marble and granite (polished)Concrete: sealed, polished, epoxy-coatedCork flooringLinoleum and MarmoleumRough or textured hard floors: NR+CR rubber provides maximum grip on smooth surfaces. On rough, textured floors (unsealed concrete, natural cleft slate, travertine), the grip may be excessive and make furniture nearly impossible to reposition. For rough floors, use round self-adhesive furniture slides instead. The hard ABS base handles abrasive textures without excessive grip.

Furniture on boats, yachts, and cruise ships faces constant lateral force from wave motion, engine vibration, and course changes. Round non-slip self-adhesive furniture glides are built for exactly this environment.

Why NR+CR works on water

The chloroprene rubber (CR) component resists salt spray, UV exposure from cabin windows and open decks, and the constant humidity cycling that degrades natural rubber. The high-friction NR+CR surface holds furniture in position against wave-induced lateral forces on sealed teak, fiberglass, or cabin flooring.

Self-adhesive mounting is ideal for marine furniture on metal and composite frames that can't accept a rivet.

Marine-specific benefits

Extra-high-bond acrylic foam adhesive resists the constant vibration that loosens commodity adhesives. The closed-cell foam conforms to minor surface irregularities on marine-grade leg materials.

NR+CR rubber is non-staining on sealed teak, marine-grade vinyl, fiberglass decking, and polished cabin floors. No marks, no discoloration, no residue. Non-slip furniture glides for marine environments where furniture stability is a safety requirement.

Common marine applications: bar stools and dining chairs in yacht salons and cruise ship dining rooms. Accent tables and lounge seating in cabin spaces. Any round-legged metal or composite furniture on a vessel where wave motion and vibration make standard floor protectors inadequate.

Round non-slip self-adhesive furniture glides are built on the same ABS platform and adhesive system used across the self-adhesive line. The only difference is the contact surface, which determines whether furniture holds position or moves freely.

Non-Slip: Round Self-Adhesive Furniture Glides

High-friction NR+CR rubber for round-legged furniture that must stay put. Bar stools, accent tables, display furniture, and marine seating on metal, plastic, or hollow tube legs. These are the non-slip self-adhesive furniture glides you're viewing now.

You're viewing this product.Smooth Glide: Round Self-Adhesive Furniture Glides

Low-friction PA6 fiber for round-legged furniture that repositions regularly. Dining chairs, kitchen chairs, desk seating. Anything that should move silently.

For furniture that needs to glide →

Both variants use the same ABS platform and acrylic foam adhesive. Only the floor-contact surface differs: NR+CR for grip, PA6 for movement.

The glide shape must match the leg cross-section. All three non-slip shapes use the same NR+CR surface, ABS platform, and acrylic foam adhesive.

Round Non-Slip ← You're here.

For circular, turned, tapered, and cylindrical legs. Available from Ø 7/8" (23 mm) to Ø 3" (75 mm).

Square Non-Slip

For equal-sided square legs. Full corner-to-corner grip. Available from 7/8" x 7/8" (23 x 23 mm) to 3" x 3" (75 x 75 mm).

View square non-slip self-adhesive furniture glides →

Rectangular Non-Slip

For rectangular legs with unequal sides. 1-5/16" x 3/4" (33 x 19 mm).

View rectangular non-slip self-adhesive furniture glides →