Hospitality-grade floor protection · Free shipping over $50 · 90-day limited warranty
Hospitality-grade floor protection · Free shipping over $50 · 90-day limited warranty
Sled base furniture rides on curved metal runners instead of individual legs. Every contact point where bare metal meets the floor is a scratch waiting to happen. Sled base glides mount to the runner at every floor contact position: straight sections, bends, and tube ends. Polyamide saddle glides cradle the round tube runner and provide smooth, non-scratching floor contact across the entire frame. Works on all hard floors and on carpet, carpet tile, and area rugs.
Works on all hard floors and carpet·Mid-runner, corner, end, and clip-on positions·Round, rectangular, and oval tube profiles
A sled base frame has three distinct zones that need floor protection. Mid-runner glides cover the straight sections. Corner glides cover the bends. End glides and clip-on glides cover the tube ends. Choose based on where the tube contacts the floor.
MID-RUNNER
For straight horizontal sections of the runner where the tube lies flat on the floor. The saddle cradles the tube from below. Screw-mount through the tube wall.
CORNER
For the bend where the runner curves into the vertical riser. The extended base spans the full transition zone. The bend is often the highest-stress contact point on a sled chair.
END / CLIP-ON
For open tube ends and wireframe sled furniture. End glides insert into the tube end. Clip-on glides snap onto wireframe runners without screws.
For the straight horizontal sections of the runner. The polyamide saddle cradles the tube from below and is secured with screws through the tube wall. Tube diameters from Ø 20 to Ø 30 mm in multiple base shapes. Five variants give you the right footprint for everything from lightweight residential to heavy commercial sled furniture.
Ø 20 mm tube. Standard-height mid-runner for lightweight sled furniture.
Ø 25 mm tube. Compact footprint for standard sled chairs.
Ø 28 mm tube. Pad slot for heavy commercial sled furniture.
Ø 20, Ø 28 mm tubes. Round footprint with PA6 pad slot.
Ø 20, Ø 30 mm tubes. Extended footprint with PA6 pad slot.
For the bend where the horizontal runner curves upward into the vertical riser. The extended base spans the full transition zone. Mid-runner glides cannot fit here because the tube is curved. Three configurations cover single-screw mount, standard two-screw mount, and pad-slot version for scratch-sensitive floors.
Ø 25 mm tube. Two-screw mount. Flat polyamide base.
Ø 20 mm tube. Single-screw mount. Flat polyamide base.
Ø 28 mm tube. Two-screw mount. PA6 pad slot.
For open tube ends and wireframe sled furniture. End glides are inserted into the tube end and secured with screws. Clip-on glides snap onto Ø 10 mm wireframe runners without any fasteners. Three tube shapes (round, rectangular, oval) plus the clip-on wireframe option cover the full range of sled tube terminations.
Ø 28 mm. PA6 pad slot. Screw mount. For open round tube ends.
For rectangular tube profiles on sled furniture.
For oval tube profiles on sled furniture.
Ø 10 mm wireframe runner. No screws. Friction clip.
For furniture that contacts the floor along a straight edge rather than a round tube runner. Mounts along flat bottom rails, rocking chair runners, and any straight floor-contact edge where saddle-mount glides cannot provide coverage. Nail-on installation instead of saddle screw-mount.
15 × 45 mm. Nail-on polyamide body. For flat-bottom rails, rocking chair runners, bench bases, and straight floor-contact edges. Available in Black, Brown, and Natural.
Sled base glides work on all hard floors and on carpet, carpet tile, and area rugs. The polyamide saddle is abrasion-resistant and handles both smooth and textured surfaces. Pad slot products give you the option to add a PA6 pad for scratch-sensitive floors.
ALL HARD FLOORS + CARPET
The bare polyamide saddle works across every floor type. Smooth hardwood, vinyl, laminate, and tile. Textured tile, slate, stamped concrete, and brushed stone. Carpet, carpet tile, and area rugs. The saddle slides smoothly without snagging carpet pile or wearing on abrasive surfaces.
SMOOTH HARDWOOD + LVP
For pad slot products, fit a PA6 pad into the slot to optimize the glide for scratch-sensitive smooth floors: hardwood, luxury vinyl, laminate. The needle-punched fiber pad provides extra-soft floor contact for finished surfaces that show wear easily. Use without the pad for everything else.
Both protect floors from furniture, but the underlying furniture geometry decides which one fits. Sled base furniture rides on a continuous metal runner; standard furniture rests on individual legs.
SLED BASE GLIDES
Polyamide saddle glides that cradle the round tube runner from below. Screw-mount or friction clip-on. Multiple mounting positions: mid-runner, corner, and tube end. Sized by tube diameter (Ø 10 to Ø 30 mm). Best for cantilever chairs, U-frame chairs, sled-base stools, wireframe seating, and any furniture with a continuous tube runner that contacts the floor.
STANDARD FURNITURE GLIDES
PA6 fiber or anti-slip rubber surface on an ABS platform. Nail-on or self-adhesive. Mounted to the bottom of each leg. Sized by leg cross-section: round (Ø 23 to Ø 75 mm), square (23 × 23 to 75 × 75 mm), or rectangular. Best for dining chairs, tables, desks, bar stools, and any standard furniture with four discrete legs.
Any sled base furniture on any floor type: hard floors, carpet, carpet tile, and area rugs. For bulk and commercial orders, visit Business Solutions.
🎓
Classroom stacking chairs, student seating, and lecture hall furniture
🏥
Waiting room chairs, patient seating, institutional sled furniture
💼
Conference chairs, visitor seating, cantilever desk chairs
🍽
Sled dining chairs on tile, stone, and hardwood floors
🏛
Airport seating, library chairs, government buildings, churches
🏠
Cantilever dining chairs, home office sled seating on hardwood
Two installation methods depending on the glide type. Saddle glides bolt onto the tube with self-tapping screws. Clip-on glides snap on without fasteners.
SCREW-MOUNT
Position the glide on the runner so the saddle cradles the tube. Mark and pre-drill through the tube wall using the holes in the glide as a guide. Drive self-tapping screws through the glide into the tube. The saddle should sit snug against the tube with no gap. Screws not included. Source self-tapping screws sized for your tube wall thickness.
FRICTION CLIP-ON
Press the clip-on glide onto the runner end. The friction clip grips the tube without screws. Slide along the tube to the position. No tools, no fasteners. For Ø 10 mm wireframe runners only. Removable and reusable.
Get it right before you order.
Selection Guide
Tube diameter, mounting position, base shape, and pad slot options. Walks through every decision point for sled base furniture.
Measurement Guide
Measure the outside diameter of the tube runner accurately. Tips for round, oval, and rectangular tube profiles.
Installation Guide
Step-by-step install for screw-mount saddle glides and clip-on glides. Tips for tube prep, screw selection, and replacement on existing furniture.
Browse other product categories: Furniture Glides · Furniture Slides · Furniture Pads · Tube Plugs & End Caps · Adjustable Leveling Feet
Other product guides: Glides Guide · Slides Guide · Pads Guide · Tube Plugs Guide · Leveling Feet Guide
Business accounts: Business Solutions for volume pricing, B2B accounts, hospitality fit-outs, and commercial orders.
