Hospitality-grade floor protection · Sizing help before you order · Apply for a business account
Sizing help · Apply for a business account
Hospitality-grade floor protection · Sizing help before you order · Apply for a business account
Sizing help · Apply for a business account
Bare rectangular legs scratch hard floors, and a round glide leaves the corners exposed. These cover the leg ends in PA6 fiber, with EHBF acrylic adhesive that bonds to metal, plastic, chrome, and wood. No drilling, no tools. Fits rectangular legs up to 40 × 25 mm.
We make this size in production runs, so there is none on the shelf today. Tell us how many you would want and you go on the list for it. When enough people ask for a size, we run it, and the people who asked hear about it first.
Buying in volume? See business pricing & samples ↓
Rectangular metal legs, sled frames, and hollow tube rails can’t accept a nail-on rivet. But they still need the same end-to-end PA6 protection that keeps hardwood, tile, laminate, and vinyl scratch-free.
Rectangular self-adhesive furniture glides use EHBF (red) acrylic foam adhesive to bond a PA6 needle-punched fiber surface to any clean, smooth rectangular leg. Silent, low-friction movement on every smooth, hard floor. Peel-and-stick floor protectors for mid-century and Scandinavian furniture where a rivet isn’t an option.
Peel the backing, align the long axis, press firmly for 30 seconds. Allow 48 hours for full adhesive cure before heavy use. The EHBF adhesive builds bond strength progressively over 48 hours under the furniture’s own weight.
Rectangular self-adhesive furniture glides come in one precision size: 33 × 19 mm, fitting rectangular legs up to 40 × 25 mm. Self-adhesive floor protectors for rectangular legs on every smooth, hard floor. For any leg material.
Measure the leg base to find the right size. Rectangular legs have two different dimensions: length and width. You need both numbers.
Lay the piece on its side or turn it upside down. You need full access to the flat bottom face of each leg where the rectangular self-adhesive furniture glide will bond.
Place a ruler across the longer edge of the leg base. Record in millimeters. Then measure the shorter edge. If both sides are equal, the leg is square. Use square self-adhesive furniture glides instead.
On sled-base furniture, measure each contact point individually. As long as all points fall within 33–40 mm × 19–25 mm, the same glide fits every contact point.
No tools. No drilling. No hardware. Every rectangular self-adhesive furniture glide comes with EHBF (red) adhesive pre-applied.
Peel the backing, align the long axis, press firmly. The whole job takes less time than reading this section.
PA6 is chemically inert and leaves no marks, scuffs, or residue on any sealed floor finish. The National Wood Flooring Association (NWFA) recommends furniture protectors on every leg as a primary hardwood maintenance step.
Rectangular self-adhesive furniture glides deliver silent, low-friction movement without scratching. These hardwood floor protectors are built for long-term performance on every surface listed below.
Rectangular self-adhesive furniture glides are built on the same ABS platform and adhesive system used across the self-adhesive line. The only difference is the contact surface, which determines whether furniture moves freely or holds position.
Low-friction PA6 fiber for rectangular-legged furniture that repositions regularly. Mid-century dining chairs, Scandinavian side chairs, sled-frame seating on metal, plastic, or hollow tube legs. These are the mid-century chair glides you are viewing now.
Controlled end-to-end grip for rectangular-legged furniture that must stay put. Mid-century accent tables, display furniture, and any rectangular-legged piece where sliding is a problem or safety concern.
Both variants use the same ABS platform and acrylic adhesive. Only the floor-contact surface differs: PA6 for movement, NR+CR for grip.
The glide shape must match the leg cross-section. All three Smooth Glide shapes use the same PA6 surface, ABS platform, and acrylic adhesive.
For circular, turned, tapered, and cylindrical legs. from Ø 23 mm to Ø 75 mm.
For equal-sided square legs. Full corner-to-corner PA6 coverage. from 23 × 23 mm to 75 × 75 mm.
For rectangular legs with unequal sides. Full end-to-end PA6 coverage. 33 × 19 mm.
It was scratched by the pad you put there to protect it. Here is how that happens, and what we do differently.
It picks up sand and grit from the floor and holds it there. Every time the chair moves, that grit is dragged across the finish. The pad is still doing its job, and it is the thing causing the damage.
Vertical fiber, not a flat mat. It does not trap debris the way flat felt does, and it is built to take repeated movement without compressing flat.
| What happens | Cheap felt pad | Superior Glide |
|---|---|---|
| Structure | Flat, matted fiber with an open surface | PA6 needle-punched fiber |
| Grit | Absorbs it and holds it against the floor finish | Does not trap debris the way flat felt does |
| Under weight | Compresses, and stays compressed | Built to take repeated movement without compressing flat |
| Staying on | Hardware-store pressure-sensitive backing creeps under sideways load and lets go at the leg face | EHBF acrylic foam. Clean the leg, peel, press for 30 seconds, allow 48 hours to cure |
| Fit | An assortment pack, and you hope one size lands | Sized to your leg. Measure the base, order the size that sits flush or just inside it |
| Floor match | Sold as suitable for every floor | Matched to your floor. PA6 fiber for smooth hard floors, ABS for carpet and rough floors |
These glides are for smooth hard floors: hardwood, engineered wood, laminate, luxury vinyl, linoleum, cork and polished tile. For carpet, textured tile, or any floor with deep grout lines, you want furniture slides instead.
| Size | Fits legs measuring |
|---|---|
| 33 × 19 mm (1.30″ × 0.75″) | 33 × 19 to 40 × 25 mm (1.30″ × 0.75″ to 1.57″ × 0.98″) |
Measure the flat base of the leg and choose the size in that row. The glide sits flush with the leg base or just inside it, never wider. For legs over 95 mm (3.74″), use a self-adhesive furniture pad, which is sized to the leg rather than fitted to it.
One sheet covers round, square, and rectangular legs, for both nail-on and self-adhesive versions.
Printable size guide (PDF)Print at 100% actual size, then hold your leg against each shape.
| Specification | Detail |
|---|---|
| Material | ABS, PA6 polyamide fiber, EHBF acrylic foam adhesive |
| Sizes | 33 × 19 mm (1.30″ × 0.75″) |
| Height (H) | 12 mm (0.47″) |
| Mounting | EHBF acrylic foam adhesive |
| Colors | Black |
| Floor compatibility | Smooth hard floors only |
| Fitting | Clean the leg with 70% isopropyl alcohol, peel, press firmly for 30 seconds, allow 48 hours to cure. |
| Minimum order | Sold in a minimum of 4, then any quantity you need |
A round glide inscribed inside a rectangular leg leaves both long edges and both narrow ends exposed. Those unprotected sections bear directly on the floor, especially along the long axis where rectangular legs carry the most weight. Rectangular self-adhesive furniture glides match the full footprint end to end, edge to edge, so every millimeter is protected by PA6 fiber.
Rectangular self-adhesive furniture glides come in one precision size: 33 × 19 mm. They fit rectangular legs from 33 × 19 mm up to 40 × 25 mm, which covers the vast majority of mid-century, Scandinavian, transitional, and contemporary rectangular legs. If your leg exceeds 40 × 25 mm, rectangular self-adhesive furniture pads offer in 6 width groups for an exact dimensional match.
EHBF acrylic adhesive bonds to wood, steel, aluminum, chrome, stainless steel, plastic, powder-coated metal, and composite materials. This makes rectangular self-adhesive furniture glides the right choice for metal sled-base furniture, chrome-legged mid-century chairs, and plastic or composite frames where a nail-on rivet isn’t possible. The adhesive builds bond strength progressively over 24 hours.
Both use the same ABS platform and acrylic adhesive. The difference is the floor-contact surface. Rectangular self-adhesive furniture glides (Smooth Glide) use low-friction PA6 fiber for furniture that needs to move freely, like mid-century dining chairs. Rectangular anti-slip self-adhesive furniture glides use NR+CR rubber for furniture that must stay put, like accent tables. Choose based on the job: movement or grip.
Measure the flat contact area at the base of each runner, not the tube cross-section. Clean each contact point with isopropyl alcohol. Peel the backing, align the glide’s long edge with the runner’s long edge, and press firmly for 30 seconds. If the sled frame has multiple contact points per side, each point needs its own glide. The EHBF adhesive reaches full bond strength after 24 hours under the furniture’s own weight.
Rectangular metal or plastic legs where nothing can be nailed. One glide bonds corner to corner across the leg face, so the whole footprint slides on PA6 rather than bare metal.
Rectangular Self-Adhesive Furniture Glides
Outfitting a hotel, restaurant, school, healthcare facility, or large furniture build? Superior Glide supports volume orders with bulk pricing tiers, free physical samples, and dedicated quote pricing for accounts placing larger orders.
Bulk pricing tiers, net terms for qualified buyers, and dedicated support for facility managers and procurement teams.
Hold the product, test the fit, check the finish. We ship samples free so you can evaluate before committing to a full order.
For orders above standard volume tiers, we’ll prepare a custom quote with consolidated shipping and your account’s tier pricing.
Reviews
There are no reviews yet