Round self-adhesive furniture glides protect smooth, hard floors from scratches. PA6 needle-punched fiber glides silently with no scuffing or marks. EHBF acrylic adhesive bonds to metal, plastic, chrome, and wood. No drilling, no tools.
Not sure what size? See the size chart ↓
📦 Sold in packs of 4 — quantity adjustable at checkout
Metal, plastic, chrome, and hollow tube legs can’t accept a nail-on rivet. But they still need the same PA6 needle-punched fiber protection that keeps hardwood, tile, laminate, and vinyl scratch-free.
Round self-adhesive furniture glides use EHBF acrylic adhesive to bond the same PA6 surface to any clean, smooth round leg. Silent, low-friction movement on every smooth, hard floor. These are the peel-and-stick chair leg protectors and peel-and-stick floor protectors for furniture where a rivet isn’t an option.
Peel the backing, center the glide, Press firmly for 30 seconds. Allow 48 hours for full adhesive cure before heavy use. The EHBF adhesive builds bond strength progressively over 24 hours under the furniture’s own weight.
Round self-adhesive furniture glides come in from Ø 23 mm to Ø 75 mm. Self-adhesive chair leg protectors for round legs on hardwood, tile, laminate, vinyl, stone, and every other smooth, hard floor. For any round leg material. Sold in multiples of 4.
Five diameters cover every standard round furniture leg. The glide should be slightly smaller than the leg diameter so it stays hidden beneath the leg edge.
If your measurement lands on a boundary, choose the smaller round self-adhesive furniture glide.
For legs Ø 23–27 mmSide chairs, lightweight accent furniture
For legs Ø 28–37 mmDining chairs, kitchen chairs, bar stools
For legs Ø 38–49 mmAccent chairs, heavier seating, counter stools
For legs Ø 50–74 mmAccent tables, display furniture, and equipment
For legs Ø 75 mm and aboveLarge tables, heavy commercial furniture
For solid wood legs, round nail-on furniture glides use a tubular rivet instead of adhesive. For anti-slip grip, round anti-slip self-adhesive furniture glides use NR+CR rubber. For bulk orders, visit Business Solutions.
Measure the leg base to find the right size. The most common mistake is guessing the leg size.
A glide that’s too large overhangs and peels. A glide that’s too small leaves the leg perimeter in direct contact with the floor. With measuring takes 30 seconds.
Lay the piece on its side or turn it upside down. You need full access to the flat bottom face of each leg where the round self-adhesive furniture glide will bond.
Use a ruler or calipers across the widest point of the leg base. For tapered legs, measure at the very bottom. The base is the only measurement that matters.
Select the round self-adhesive furniture glide whose range includes your measurement. If you’re on a boundary, go with the smaller size so the glide stays inside the leg edge.
No tools. No drilling. No hardware. Every round self-adhesive furniture glide comes with EHBF adhesive pre-applied.
Peel the backing, center the glide, press firmly. The whole job takes less time than reading this section.
PA6 is chemically inert and leaves no marks, scuffs, or residue on any sealed floor finish. The National Wood Flooring Association (NWFA) recommends furniture protectors on every leg as a primary hardwood maintenance step.
Round self-adhesive furniture glides meet that standard across every smooth, hard floor type. These hardwood floor protectors are safe for every surface listed below.
Three components work together in every round self-adhesive furniture glide. One touches your floor. One bonds the glide to your furniture leg. One sits between them and distributes the load.
PA6 fibers are forced through the base material by thousands of barbed needles during manufacturing. Each fiber is mechanically interlocked with its neighbors. No glue holding it together. No layers to separate.
Unlike cheap felt pads that compress and trap grit, PA6 deflects debris and maintains its smooth surface through extended daily use on hardwood, tile, and every other sealed floor.
EHBF is a double-sided self-adhesive fiberglass mesh tape that bonds the ABS platform to any smooth leg surface. Unlike commodity double-sided tape that peels under lateral stress, EHBF builds bond strength progressively under the furniture’s own weight.
The fiberglass mesh provides shear resistance that prevents the creep and stretch that peel cheap adhesive off furniture legs.
The rigid circular disc between the PA6 surface and the EHBF adhesive layer distributes compression load evenly across the full glide surface. No concentrated stress at the edges, no curling under asymmetric weight.
If you’ve been replacing felt pads every few months or wondering why your chair leg protectors keep peeling off, here’s how self-adhesive floor protectors compare to the alternatives.
Felt compresses flat under load, absorbs moisture from floor cleaning, and traps abrasive grit that scratches the finish. The adhesive on cheap felt peels within weeks.
PA6 needle-punched fiber can’t compress flat, doesn’t absorb moisture, and deflects debris instead of trapping it. EHBF fiberglass mesh adhesive resists the creep that peels cheap felt off furniture legs.
Same PA6 surface, same ABS platform. The difference is the attachment method. Round nail-on furniture glides use a tubular rivet for solid wood, providing the strongest possible mechanical bond.
Round self-adhesive furniture glides use EHBF adhesive for metal, plastic, chrome, hollow tube, or any leg where a rivet isn’t possible. Choose based on leg material.
Same ABS platform, same EHBF adhesive, same sizes. Opposite function. Round anti-slip self-adhesive furniture glides use NR+CR rubber for furniture that must stay put. Round self-adhesive furniture glides use PA6 for furniture that needs to move freely. Choose based on the job: movement or grip.
Silicone provides moderate grip but leaves oily residue on floor finishes. PA6 provides smooth, low-friction movement without residue, marks, or scuffs. Clean removal when the glide is eventually replaced.
Round self-adhesive furniture glides share the same ABS platform and adhesive as the anti-slip range. The only difference is the contact surface, which determines whether furniture moves freely or holds position.
Low-friction PA6 fiber for round-legged furniture that repositions regularly. Dining chairs, kitchen chairs, desk seating, and accent chairs on metal, plastic, or hollow tube legs. These are the self-adhesive chair glides for hardwood floors you’re viewing now.
Controlled grip for round-legged furniture that must stay put. Bar stools, accent tables, and display furniture on metal, plastic, or hollow tube legs. Anywhere sliding is a problem or a safety concern.
Both variants use the same ABS platform and acrylic adhesive. Only the floor-contact surface differs: PA6 for movement, NR+CR for grip.
The glide shape must match the leg cross-section. All three Smooth Glide shapes use the same PA6 surface, ABS platform, and acrylic adhesive.
For circular, turned, tapered, and cylindrical legs. from Ø 23 mm to Ø 75 mm.
For equal-sided square legs. Full corner-to-corner PA6 coverage. from 23 × 23 mm to 75 × 75 mm.
For rectangular legs with unequal sides. Mid-century and Scandinavian furniture. 33 × 19 mm.
Any situation where round non-wood legs meet smooth, hard flooring, and the furniture needs to move freely. These are the professional-grade peel-and-stick furniture floor protectors for metal, plastic, and composite round-legged furniture when felt pads fail, rubber caps drag, and nail-on rivets aren’t possible.
Metal dining chairs on hardwood are the single most common residential application. Chrome bar stools, kitchen chairs on steel frames, accent chairs on brushed metal legs, and any round-legged metal or plastic furniture on smooth, hard floors.
Self-adhesive chair leg protectors that put PA6 protection within reach of every homeowner. No tools, no experience required.
Restaurant dining chairs on metal frames. Hotel lobby furniture. Office seating on steel and aluminum bases. Retail display fixtures. Healthcare waiting room furniture. Event venue seating.
Available in bulk for venue fit-outs. For commercial pricing, visit Business Solutions.
Identical PA6 surface and ABS platform. ZnFe tubular rivet instead of EHBF adhesive, for solid wood legs where maximum mechanical hold is preferred.
Same ABS platform and acrylic adhesive. NR+CR rubber surface instead of PA6, for round-legged furniture that must hold position on smooth, hard floors.
| Specification | Details |
|---|---|
Product Type |
Self-Adhesive Furniture Glides |
Shape |
Round |
Surface Material |
PA6 Needle-Punched Polyamide 6 |
Platform Material |
ABS Acrylonitrile Butadiene Styrene |
Adhesive |
EHBF Extra High Bond Foam Acrylic Tape |
Pile Density |
1,450 g/m² |
Leg Compatibility |
Solid wood, metal, and plastic legs |
Floor Compatibility |
Smooth, hard floors |
Sizes Available |
Ø 23 mm – Ø 75 mm (0.91″ – 2.95″) |
Pack Quantity |
Sold in multiples of 4 |
Color |
Black |
Installation |
Press firmly for 30 seconds. Allow 48 hours before heavy use |
Indoor/Outdoor Use |
Indoor | Covered Outdoor |
| Ø (Diameter) | Compatible Leg Size | H (Height) | Weight |
|---|---|---|---|
28 mm (1.10") |
23 – 27 mm (0.91 – 1.06″) |
12 mm (0.47") |
2.5 g |
28 mm (1.10") |
28 – 37 mm (1.10 – 1.46″) |
12 mm (0.47") |
3.4 g |
38 mm (1.50") |
38 – 49 mm (1.50 – 1.93″) |
12 mm (0.47") |
6.5 g |
50 mm (1.97") |
50 – 74 mm (1.97 – 2.91″) |
12 mm (0.47") |
12.8 g |
75 mm (2.95") |
75 mm and above (2.95″+) |
12 mm (0.47") |
28.1 g |
PA6 stands for Polyamide 6, a needle-punched synthetic fiber with a pile density of 1,450 g/m². Thousands of barbed needles mechanically interlock the fibers during manufacturing, so no glue holds the surface together. The result is a dense, low-friction contact layer that deflects debris, resists compression, and glides silently across hardwood, tile, laminate, vinyl, and stone. PA6 won’t absorb moisture, trap grit, or stain any sealed floor finish.
EHBF acrylic adhesive bonds to wood, steel, aluminum, chrome, stainless steel, plastic, powder-coated metal, and composite materials. On chrome legs, clean thoroughly before application for the strongest bond. On plastic legs with low surface tension, test adhesion on a small area first. Some plastics may need an adhesion promoter. The adhesive builds bond strength progressively over 24 hours under the furniture’s own weight.
Both use the same PA6 surface and ABS platform. The difference is the attachment method. Round nail-on furniture glides use a ZnFe tubular rivet for solid wood legs, providing the strongest possible mechanical bond. Round self-adhesive furniture glides use EHBF acrylic adhesive for metal, plastic, chrome, hollow tube, or any leg where a rivet isn’t possible. Choose based on leg material.
Both use the same ABS platform and acrylic adhesive. The difference is the floor-contact surface. Round self-adhesive furniture glides (Smooth Glide) use low-friction PA6 fiber for furniture that needs to move freely, like dining chairs. Round anti-slip self-adhesive furniture glides use NR+CR rubber for furniture that must stay put, like bar stools. Choose based on the job: movement or grip.
Yes. PA6 is chemically inert and non-staining on all sealed floor finishes, including LVP, LVT, and sheet vinyl. The National Wood Flooring Association (NWFA) recommends furniture protectors on every leg as a primary maintenance step. PA6 will not discolor, mark, or leave residue on light-colored vinyl or any other sealed smooth, hard floor.
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet