Square furniture legs need square anti-slip glides — a round rubber pad on a square leg loses grip at all four corners. Square anti-slip nail-on furniture glides use a 30 Shore A NR+CR (Natural Rubber + Chloroprene Rubber) surface that grips hardwood, tile, laminate, vinyl, and stone across the full corner-to-corner footprint. The zinc-plated tubular rivet with anti-rotation mortise locks mechanically into solid wooden legs — the strongest possible connection between glide and furniture, with zero risk of the glide spinning out of alignment. 5 sizes from 23 × 23 mm to 75 × 75 mm. Available in multiples of 4. The professional choice for square-legged furniture that must stay exactly where you place it.
Not sure what size? See the size chart ↓
📦 Sold in packs of 4 — quantity adjustable at checkout
Square anti-slip nail-on furniture glides for hard floors provide full corner-to-corner grip for square wooden furniture legs on smooth hardwood, tile, laminate, vinyl, and stone. A round anti-slip glide on a square leg loses rubber contact at all four corners — the exact points where grip matters most. These square anti-slip nail-on furniture glides cover every corner edge to edge, maximizing the NR+CR rubber-to-floor contact area for the strongest possible hold. The 30 Shore A NR+CR (Natural Rubber + Chloroprene Rubber) surface grips the floor under compression, and the zinc-plated tubular rivet with anti-rotation mortise locks into solid wood — preventing both detachment and the rotational misalignment that would expose unprotected corners.
5 sizes from 23 × 23 mm to 75 × 75 mm. Available in multiples of 4. For wooden furniture legs only. For metal, plastic, or hollow legs, use square anti-slip self-adhesive furniture glides.
Square anti-slip nail-on furniture glides for hard floors are available in five sizes to match the actual base of the leg. Correct sizing is critical on anti-slip glides — an undersized glide reduces the rubber contact area and grip strength at the corners, and an oversized glide overhangs and catches on floor transitions.
For legs 23–27 × 23–27 mm
Lightweight accent furniture
For legs 28–37 × 28–37 mm
Side tables, display furniture
For legs 38–49 × 38–49 mm
Accent chairs, bookcases
For legs 50–74 × 50–74 mm
Dining tables, heavy cabinets
For legs 75 × 75 mm and above
Conference tables, executive furniture
Need a wider range of square sizes for standard PA6 glides? Square self-adhesive furniture pads are available in 31 sizes from 20 × 20 mm to 300 × 300 mm. For bulk orders and commercial fit-outs, visit Business Solutions.
Correct sizing is even more important on square anti-slip glides than on standard PA6 glides. Every square millimeter of NR+CR rubber contact contributes to grip strength — and on square legs, the four corners are the highest-load contact zones. An undersized square anti-slip nail-on furniture glide leaves the corners unprotected and reduces grip exactly where it matters most. Take 30 seconds to measure before you order.
Lay it on its side or flip it upside down. You need clear access to the base of each leg where the square anti-slip nail-on furniture glide will sit.
Use a steel rule or calipers. Measure across both sides of the leg base independently. If the two measurements differ by more than 3 mm, the leg is rectangular — use rectangular anti-slip nail-on furniture glides instead.
Select the square anti-slip nail-on furniture glide whose range includes your measurement. When a measurement falls exactly on a boundary (e.g., 38 mm), choose the larger size — more rubber contact area means stronger grip.
Installing square anti-slip nail-on furniture glides takes under a minute per leg. No pre-drilling required on any hardwood, MDF, or softwood species. Corner alignment during installation is critical — the anti-rotation mortise locks after the rivet is seated, and on anti-slip glides a misaligned corner means reduced rubber contact and reduced grip.
Square legs are common on Shaker, mission, farmhouse, Arts & Crafts, and contemporary furniture — styles that prioritize stability and architectural presence. These are often pieces that anchor a room: dining tables, bookcases, display cabinets, accent chairs. When they drift out of position on smooth hard floors, the room loses its layout. Square anti-slip nail-on furniture glides keep them exactly where they belong.
Smooth hard floors have a low coefficient of friction by design — the same property that makes them easy to clean also lets furniture migrate. Square legs concentrate weight at the four corners, creating high-pressure contact points that reduce friction further. The result is heavy furniture that still drifts millimeters at a time, accumulating into visible displacement.
Square anti-slip nail-on furniture glides for hard floors solve this by placing high-friction NR+CR rubber across the full square footprint — including all four corners. The rubber conforms to floor micro-texture under compression, and grip increases with furniture weight rather than decreasing.
These square anti-slip nail-on furniture glides for hard floors use a chemically inert NR+CR rubber surface that does not react to floor sealers, waxes, or cleaning solutions. The rubber will not stain, discolor, or mark finished floors. The National Wood Flooring Association (NWFA) recommends placing protective glides on all furniture legs as a primary measure for maintaining hardwood floor condition — the NR+CR rubber surface on these square anti-slip nail-on furniture glides meets that standard while adding the grip that PA6 glides cannot provide. Compatible with every smooth hard floor type.
Every component in these square anti-slip nail-on furniture glides for hard floors is specified for a particular engineering reason. The NR+CR rubber surface provides the grip. The ABS platform distributes load evenly across all four corners. The ZnFe rivet with mortise locks it all permanently to the wood — and prevents it from spinning.
The NR+CR rubber surface on these square anti-slip nail-on furniture glides is rated at 30 Shore A hardness — soft enough to conform to micro-texture on smooth hard floors, firm enough to support furniture weight without excessive compression. The Shore A durometer scale measures rubber hardness — 30A sits in the range between soft grip compounds and structural rubber, the ideal balance for floor-contact applications.
On square legs, corner contact is the key advantage over round anti-slip glides. A round glide inscribed inside a square leg leaves the four corners without rubber contact — the high-load zones where grip is needed most. Square anti-slip nail-on furniture glides for hard floors place rubber at every corner, every edge, and across the full square footprint. More rubber contact area means stronger grip.
The rivet’s razor-sharp tubular edge separates wood fibers rather than removing them. The entry hole closes back when the rivet is removed — unlike a plain nail hole, which widens with every movement and replacement.
On square anti-slip nail-on furniture glides, the anti-rotation mortise serves a dual purpose. It prevents the glide from spinning — which on a square glide would expose unprotected corners. And because the rubber surface generates resistance forces that create rotational torque on the mounting, the mortise absorbs that torque without allowing the alignment to shift. The strongest possible connection between glide and furniture.
The rigid platform that carries both the NR+CR rubber surface and the rivet. ABS distributes the furniture’s weight evenly across all four corners — maximizing rubber contact at the high-load zones. Without the rigid platform, the rubber would compress unevenly under corner loads, reducing the effective grip area at the exact points where it matters most.
Cheap stick-on rubber pads and silicone dots use thin material on a weak adhesive backing. On square legs, the four corners bear the highest load — the exact points where cheap adhesive fails first. Within weeks, the pads peel off the corners and end up on the floor instead of the furniture leg.
Square anti-slip nail-on furniture glides for hard floors use 30 Shore A NR+CR rubber on a rigid ABS platform, mechanically riveted into solid wood. The rivet cannot peel. The platform distributes load evenly across all four corners. The rubber surface on these square anti-slip nail-on furniture glides is thick enough to conform to floor micro-texture for maximum grip — not a thin film that provides minimal friction.
A round anti-slip glide inscribed inside a square leg leaves all four corners without rubber contact. Those corners bear the highest load concentration on a square leg — and they are the exact points where grip is needed most to prevent furniture drift. A round glide on a square leg also provides no rotational resistance — every orientation is equivalent, so the glide can spin freely.
Square anti-slip nail-on furniture glides for hard floors cover every corner, every edge, and every millimeter of the square footprint. The anti-rotation mortise keeps the corners permanently aligned with the leg. Full rubber contact at every corner. Maximum grip from every square millimeter.
Standard PA6 square nail-on furniture glides are designed for low friction — they help furniture slide smoothly. If the furniture is drifting, creeping, or migrating on smooth floors and you want it to stop, PA6 glides will not solve the problem. They are engineered to do the opposite.
Square anti-slip nail-on furniture glides for hard floors use NR+CR rubber instead of PA6 — a high-friction surface instead of a low-friction surface. Same ABS platform. Same ZnFe rivet with anti-rotation mortise. Opposite result. View standard PA6 square nail-on furniture glides →
Square self-adhesive furniture pads use a PA6 needle-punched surface — designed to slide, not grip. They are available in 31 sizes from 20 × 20 mm to 300 × 300 mm and are an excellent choice for furniture that should move freely on smooth hard floors in a size not available in the glide range.
If you need anti-slip grip, pads are not the right product — use these square anti-slip nail-on furniture glides or square anti-slip self-adhesive furniture glides instead. For standard PA6 floor protection without anti-slip, pads provide the widest size selection with a simpler peel-and-stick installation.
Square nail-on furniture glides come in two surface variants. Square anti-slip nail-on furniture glides use NR+CR rubber for grip; standard glides use PA6 for smooth sliding. The right choice depends on how the furniture is used — not the floor type.
For furniture that is regularly repositioned. The low-friction PA6 surface moves quietly across hardwood, tile, laminate, vinyl, and stone with minimal effort. The standard choice for dining chairs, kitchen seating, and accent furniture where ease of movement is the priority.
NR+CR rubber at 30 Shore A provides controlled grip across the full square footprint — including all four corners. Furniture stays exactly where it’s placed. The right choice for dining tables, bookcases, restaurant tables, display furniture, and any environment where an unexpected slide is a safety hazard.
Both variants use the same ABS platform and ZnFe tubular rivet with anti-rotation mortise. Only the surface material differs — PA6 for low friction, NR+CR for high friction.
Square anti-slip nail-on furniture glide shape must match the leg cross-section exactly. On anti-slip glides, shape match matters even more than on standard PA6 — every square millimeter of rubber-to-floor contact area contributes to grip strength. Measure the base before ordering.
For circular cross-section legs — turned, tapered, and cylindrical. Ø 23 / 28 / 38 / 50 / 75 mm.
For equal-sided square legs — Shaker, mission, farmhouse, and contemporary designs. Full corner-to-corner rubber grip. 23 / 28 / 38 / 50 / 75 mm.
For oblong legs with unequal sides — mid-century modern and Scandinavian furniture design. 33 × 19 mm.
Square anti-slip nail-on furniture glides for hard floors are ideal for dining tables, bookcases, cabinets, display furniture, accent chairs, side tables, and any square-legged wooden furniture that should stay in position on smooth hard floors. Also ideal for furniture near stairs, on raised platforms, or in homes with children and pets where stability is a safety concern. The 28 × 28 mm and 38 × 38 mm sizes cover the majority of residential square-legged accent furniture.
Restaurant tables, hotel lobby furniture, healthcare waiting room seating, assisted living facility furniture, retail display fixtures, boat cabin furniture, and RV built-ins. Square anti-slip nail-on furniture glides for hard floors are the preferred choice in commercial environments where unexpected furniture movement creates a liability — the anti-rotation mortise prevents the corner misalignment that high-traffic square-legged furniture experiences, and mechanical riveting provides the strongest connection. Available in bulk quantities — visit Business Solutions for commercial pricing.
Identical ABS platform and ZnFe rivet with anti-rotation mortise. PA6 low-friction sliding surface instead of NR+CR rubber — for square-legged wooden furniture that should glide freely on smooth hard floors.
Same NR+CR rubber surface. EHBF adhesive backing instead of rivet — for metal, plastic, or hollow square furniture legs that can’t accept a nail-on fitting.
| Specification | Details |
|---|---|
Product Type |
Square Anti-Slip Nail-On Furniture Glides |
Shape |
Square |
Materials |
NR+CR rubber surface, ABS base plate, ZnFe steel tubular rivet |
Shore Hardness |
30 Shore A |
Fit Style |
Nail-on tubular rivet — no pre-drilling required |
Leg Compatibility |
Solid wooden furniture legs only |
Floor Compatibility |
All hard floors — hardwood, laminate, vinyl, tile, stone, concrete, marine flooring |
Furniture Compatibility |
Chairs, stools, tables, contemporary & modern furniture, boat & yacht cabin furniture |
Sizes Available |
23 × 23 mm – 75 × 75 mm (0.91″ × 0.91″ – 2.95″ × 2.95″) |
Color Options |
Black |
Installation Type |
Tap in with hammer or rubber mallet |
Indoor/Outdoor Use |
Indoor | Covered Outdoor |
| Shape | L × W (Dimensions) | Compatible Leg/Base Size | Ø1 (Rivet Diameter) | H (Height) | H1 ( Rivet Height) |
|---|---|---|---|---|---|
Square |
23 × 23 mm (0.91″ × 0.91″) |
23 × 23 – 27 × 27 mm (0.91″ × 0.91″ – 1.06″ × 1.06″) |
9.2 mm (0.36″) |
12 mm (0.47") |
5.5 mm (0.22″) |
Square |
28 × 28 mm (1.10″ × 1.10″) |
28 × 28 – 37 × 37 mm (1.10″ × 1.10″ – 1.46″ × 1.46″) |
9.2 mm (0.36″) |
12 mm (0.47") |
5.5 mm (0.22″) |
Square |
38 × 38 mm (1.50″ × 1.50″) |
38 × 38 – 49 × 49 mm (1.50″ × 1.50″ – 1.93″ × 1.93″) |
9.2 mm (0.36″) |
12 mm (0.47") |
5.5 mm (0.22″) |
Square |
50 × 50 mm (1.97″ × 1.97″) |
50 × 50 – 74 × 74 mm (1.97″ × 1.97″ – 2.91″ × 2.91″) |
9.2 mm (0.36″) |
12 mm (0.47") |
5.5 mm (0.22″) |
Square |
75 × 75 mm (2.95″ × 2.95″) |
75 × 75 + mm (2.95″ × 2.95″+) |
9.2 mm (0.36″) |
12 mm (0.47") |
5.5 mm (0.22″) |
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet