Rectangular self-adhesive furniture glides for hard floors protect smooth hardwood, tile, laminate, vinyl, and stone from oblong furniture legs and sled frame contact points of any material — wood, metal, plastic, or hollow tube. EHBF (Extra High Bond Foam) acrylic tape bonds to any clean, smooth surface without tools. The PA6 needle-punched sliding surface (1,450 g/m² pile density) moves silently and outlasts cheap felt pads by years. Available in 33 × 19 mm (1.30″ × 0.75″). Sold in multiples of 4.
Not sure what size? See the size chart ↓
📦 Sold in packs of 4 — quantity adjustable at checkout
Rectangular self-adhesive furniture glides for hard floors protect smooth hardwood, tile, laminate, vinyl, and stone from oblong furniture legs and sled frame contact points of any material — wood, metal, plastic, or hollow tube. A round or square glide on a rectangular leg leaves the long edges unprotected and creates overhang that catches during movement.
These rectangular self-adhesive furniture glides match the oblong profile exactly: full PA6 coverage along the entire length and width. EHBF (Extra High Bond Foam) acrylic tape bonds to any clean, smooth surface without tools, drilling, or rivets. Available in 33 × 19 mm (1.30″ × 0.75″). Sold in multiples of 4.
Rectangular self-adhesive furniture glides for hard floors are available in one size designed to fit the standard oblong leg profile found on mid-century modern, Scandinavian, and contemporary furniture — as well as sled frame contact points on metal-framed seating.
For legs 33–40 × 19–25 mm
Mid-century chairs, sled frames, modern dining
Need a wider range of rectangular sizes? Rectangular self-adhesive furniture pads are available in over 100 sizes across 6 width groups, with lengths up to 300 mm and strips up to 510 mm. For bulk orders and commercial fit-outs, visit Business Solutions.
Rectangular legs have two different measurements — length and width. Both must fall within the glide’s range for a correct fit. An oversized rectangular self-adhesive furniture glide overhangs the short edges and catches during movement, peeling the adhesive bond. An undersized glide leaves the long edges in direct contact with the floor.
Lay it on its side or flip it upside down. You need clear access to the base of each leg where the rectangular self-adhesive furniture glide will sit.
Use a steel rule or calipers. Measure the long side and the short side of the leg base independently. The 33 × 19 mm rectangular self-adhesive furniture glide fits legs approximately 33–40 mm long × 19–25 mm wide.
If both measurements fall within the 33–40 × 19–25 mm range, this rectangular self-adhesive furniture glide is the correct choice. If the leg is larger, use rectangular self-adhesive furniture pads in the matching size.
Installing rectangular self-adhesive furniture glides takes under a minute per leg. No tools required. The EHBF acrylic foam tape bonds to wood, metal, plastic, and most composite surfaces. Long-axis alignment matters — a rotated glide overhangs on one end and leaves the opposite end unprotected.
These rectangular self-adhesive furniture glides for hard floors use a chemically inert PA6 surface that does not react to floor sealers, waxes, or cleaning solutions. The National Wood Flooring Association (NWFA) recommends placing protective glides on all furniture legs as a primary measure for maintaining hardwood floor condition. For a full overview of hard floor types, The Spruce’s hard flooring guide provides a useful reference.
Every component in these rectangular self-adhesive furniture glides for hard floors is specified for a particular engineering reason. The PA6 surface slides. The ABS platform distributes load across the full elongated footprint. The EHBF tape holds it all permanently to the leg.
1,450 g/m² pile density. PA6 fibers are mechanically interlocked by thousands of barbed needles during manufacturing — not glued. This is what makes PA6 rectangular self-adhesive furniture glides survive the lateral shear forces that destroy cheap felt pads.
Rectangular legs produce asymmetric lateral forces during movement — higher shear along the long axis, lower across the short axis. Cheap felt pads fail along the long edges first because the horizontal fibers shear apart under this directional loading. PA6’s vertical fiber orientation handles asymmetric shear without directional weakness. The NWFA’s hardwood floor maintenance guidelines cite abrasion from degraded furniture glides as one of the leading causes of preventable hardwood floor finish damage.
Closed-cell acrylic foam tape — the same adhesive technology used in automotive exterior trim and architectural glazing. EHBF conforms to micro-texture on the leg surface, creating mechanical interlock in addition to chemical adhesion.
On rectangular legs, asymmetric shear forces along the long axis create the worst possible loading pattern for adhesive — the peel stress concentrates at the ends. EHBF’s foam core absorbs and distributes that directional stress instead of failing at the endpoints. This is what makes rectangular self-adhesive furniture glides stay attached under repeated push-pull forces — the foam flexes with the force instead of fracturing against it.
The rigid rectangular platform that carries both the PA6 surface and the EHBF adhesive layer. ABS distributes the furniture’s weight evenly across the full elongated footprint — preventing the uneven compression that causes cheap glides to rock under the asymmetric loading that rectangular legs produce.
Cheap felt pads use horizontally-layered fibers bonded with weak adhesive. On rectangular legs, asymmetric shear along the long axis peels the felt from one end first, then progressively along the full length. The felt compresses flat and traps grit that scratches your floor.
PA6 rectangular self-adhesive furniture glides for hard floors have no adhesive layer between fibers. The vertical fiber orientation handles directional shear without weakness. And EHBF acrylic foam tape outperforms cheap felt adhesive — cheap felt peels off in weeks, EHBF holds for years.
A round glide on a rectangular leg leaves the two long edges completely unprotected — the exact edges that generate the most shear force and cause the most floor damage. A square glide oversized to cover the length creates overhang on the short sides that catches during movement and peels the adhesive bond.
Rectangular self-adhesive furniture glides for hard floors match the leg profile exactly: full PA6 coverage along the long axis, full width across the short axis. No exposed edges, no overhang, no compromise.
Use rectangular nail-on furniture glides when the legs are solid wood and the furniture moves frequently — the mechanical rivet with anti-rotation mortise provides the strongest possible connection. Use rectangular self-adhesive furniture glides when the legs are metal, plastic, hollow tube, sled frame, or any material that cannot accept a nail-on rivet.
Both use the same PA6 surface and ABS platform. The only difference is the attachment method: tubular rivet for solid wood, EHBF adhesive for everything else.
Cutting a round or square glide to fit a rectangular leg destroys the ABS platform and voids any performance guarantee. The cut edge is rough and sharp — it will scratch floors and snag during movement. A purpose-made rectangular self-adhesive furniture glide provides the correct profile, correct adhesive coverage, and correct PA6 surface integrity.
Rectangular self-adhesive furniture pads use the same PA6 needle-punched surface but without the ABS platform. Pads are available in over 100 rectangular sizes across 6 width groups with lengths up to 300 mm and strips up to 510 mm — a vastly wider size range than the single 33 × 19 mm glide.
If your rectangular leg is larger than 40 × 25 mm, pads are your only option — glides aren’t available in larger rectangular sizes. For legs that fit the 33 × 19 mm glide, the ABS platform provides a stronger, more rigid connection for high-use furniture. For furniture that moves less frequently — tables, cabinets, display pieces — pads provide excellent protection with the widest size selection.
Rectangular self-adhesive furniture glides come in two surface variants. The right choice depends on how the furniture is used — not the floor type.
For furniture that is regularly repositioned. The low-friction PA6 surface on these rectangular self-adhesive furniture glides for hard floors moves quietly across hardwood, tile, laminate, vinyl, and stone. The standard choice for mid-century dining chairs and sled frame seating.
NR+CR rubber at 30 Shore A provides controlled grip across the full rectangular footprint. Furniture stays exactly where it’s placed. Use for display furniture, accent pieces, boat cabin furniture, and any environment where an unexpected slide is a safety hazard.
Both variants use the same ABS platform and EHBF adhesive tape. Only the sliding surface differs.
Rectangular self-adhesive furniture glide shape must match the leg cross-section. A round glide on a rectangular leg leaves the long edges exposed. A square glide overhangs on the short sides. Measure the base before ordering.
For circular cross-section legs — turned, tapered, cylindrical, and tubular steel. Ø 23 / 28 / 38 / 50 / 75 mm.
For equal-sided square legs — Shaker, mission, farmhouse, and contemporary designs. 23 / 28 / 38 / 50 / 75 mm.
For oblong legs and sled frame contact points — mid-century modern, Scandinavian, and contemporary furniture. 33 × 19 mm.
Rectangular self-adhesive furniture glides for hard floors work on mid-century modern chairs, Scandinavian side tables, contemporary dining chairs, sled frame seating, display furniture, and credenzas with oblong legs on smooth hard floors. Especially useful for metal and plastic sled frames that cannot accept nail-on rivets.
Restaurant dining chairs, hotel room furniture, office seating with sled frames, conference room guest chairs, healthcare facility seating, school and classroom chairs, and event venue furniture with rectangular legs or sled bases. Rectangular self-adhesive furniture glides for hard floors bond to chrome, powder-coated steel, and anodized aluminum sled frames without tools. Available in bulk quantities — visit Business Solutions for commercial pricing.
Identical ABS platform and EHBF adhesive. NR+CR rubber surface instead of PA6 — for rectangular-legged furniture that must hold position on smooth hard floors.
Same PA6 sliding surface. Zinc-plated tubular rivet with anti-rotation mortise instead of adhesive — the strongest possible connection for solid wooden rectangular legs.
| Specification | Details |
|---|---|
Product Type |
Self-Adhesive Furniture Glides |
Shape |
Rectangular |
Materials |
PA6 pad surface, ABS base, EHBF adhesive |
Fit Style |
All hard floors |
Floor Compatibility |
Hardwood, tile, laminate, LVT, concrete, stone, bamboo, cork, vinyl |
Furniture Compatibility |
Chairs, stools, benches, tables, office seating, and other wood-leg, metal-leg, and plastic-leg furniture |
Leg Compatibility |
Wooden, metal, and plastic furniture legs |
Sizes Available |
33 × 19 mm (1.30 × 0.75") |
Color Options |
Black |
Installation Type |
Peel backing and press onto clean leg surface (wipe with 70% isopropyl alcohol first) |
Key Benefits |
Scratch prevention, noise reduction, smooth gliding, strong adhesive bond |
Indoor/Outdoor Use |
Indoor | Covered Outdoor |
| Shape | L × W (Dimensions) | Compatible Leg/Base Size | H (Height) |
|---|---|---|---|
Rectangular |
33 × 19 mm (1.30″ × 0.75″) |
33 × 19 – 40 × 25 mm (1.30″ × 0.75″ – 1.57″ × 0.98″) |
12 mm (0.47") |
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet