Some furniture shouldn’t slide. Accent chairs, side tables, display furniture, boat cabin seating — anything that needs to stay exactly where you place it on smooth hard floors. Round anti-slip nail-on furniture glides use a 30 Shore A NR+CR (Natural Rubber + Chloroprene Rubber) surface that grips hardwood, tile, laminate, vinyl, and stone. The zinc-plated tubular rivet locks mechanically into solid wooden legs — the strongest possible connection between glide and furniture. 5 sizes from Ø 23 mm to Ø 75 mm. Available in multiples of 4.
Not sure what size? See the size chart ↓
📦 Sold in packs of 4 — quantity adjustable at checkout
Round anti-slip nail-on furniture glides for hard floors are the correct solution when round-legged wooden furniture must stay exactly where you place it on smooth hardwood, tile, laminate, vinyl, and stone. Where standard PA6 glides are designed to slide, these round anti-slip nail-on furniture glides use a 30 Shore A NR+CR (Natural Rubber + Chloroprene Rubber) surface that grips the floor — preventing the passive drift, creep, and migration that smooth floors cause under even heavy furniture. The zinc-plated steel tubular rivet drives into the leg base with a rubber mallet — no pre-drilling, no prep.
5 sizes from Ø 23 mm to Ø 75 mm. Available in multiples of 4. For wooden furniture legs only. For metal, plastic, or hollow legs, use round anti-slip self-adhesive furniture glides.
Round anti-slip nail-on furniture glides for hard floors are available in five diameters to match the actual base of the leg. The glide should match the leg as closely as possible — an undersized glide reduces the rubber contact area and grip strength. An oversized glide overhangs the leg edge and may catch on floor transitions.
For legs Ø 23–27 mm
Side chairs, lightweight accent furniture
For legs Ø 28–37 mm
Dining chairs, desk chairs, side tables
For legs Ø 38–49 mm
Accent chairs, heavier seating
For legs Ø 50–74 mm
Dining tables, coffee tables, sofas
For legs Ø 75 mm and above
Conference tables, heavy commercial furniture
For bulk orders and commercial fit-outs, visit Business Solutions.
Correct sizing is even more important on anti-slip glides than on standard PA6 glides. The NR+CR rubber surface needs full contact with the floor to deliver maximum grip. An undersized round anti-slip nail-on furniture glide reduces the rubber-to-floor contact area and grip strength proportionally. Take 30 seconds to measure before you order.
Lay it on its side or flip it upside down. You need clear access to the base of each leg where the round anti-slip nail-on furniture glide will sit.
Use a steel rule or calipers. Measure straight across the widest point of the leg base. For turned legs that taper, measure at the very bottom — the actual contact point with the floor.
Select the round anti-slip nail-on furniture glide whose range includes your measurement. When a measurement falls exactly on a boundary (e.g., 38 mm), choose the larger size — more rubber contact area means stronger grip.
Installation takes under a minute per leg. No pre-drilling required on any hardwood, MDF, or softwood species.
Not every piece of furniture should move freely. Accent chairs, side tables, display furniture, bookcases, sofa end tables — anything that needs to stay exactly where you place it. On smooth hard floors, even heavy furniture drifts over time. Sitting down generates lateral force. Leaning on a table pushes it. Every movement shifts the furniture millimeters — and those millimeters accumulate into visible migration that scratches floors and creates tripping hazards.
Hardwood, tile, laminate, vinyl, polished concrete — every smooth floor type has a low coefficient of friction by design. That’s what makes them easy to clean and pleasant to walk on. But the same low friction that makes a chair easy to pull back also lets an accent table drift two inches overnight from nothing more than air current, vibration, and the micro-movements of daily life.
Round anti-slip nail-on furniture glides for hard floors solve this by placing a high-friction NR+CR rubber surface between the leg and the floor. The furniture sits on rubber instead of wood or bare PA6 — and rubber doesn’t drift.
These round anti-slip nail-on furniture glides for hard floors use a chemically inert NR+CR rubber surface that does not react to floor sealers, waxes, or cleaning solutions. The rubber will not stain, discolor, or mark finished floors. The National Wood Flooring Association (NWFA) recommends placing protective glides on all furniture legs as a primary measure for maintaining hardwood floor condition — the NR+CR rubber surface on these round anti-slip nail-on furniture glides meets that standard while adding the grip that PA6 glides cannot provide. Compatible with every smooth hard floor type.
Every component in these round anti-slip nail-on furniture glides for hard floors is specified for a particular engineering reason. The NR+CR rubber surface provides the grip. The ABS platform distributes load. The ZnFe rivet locks it all permanently to the wood.
30 Shore A hardness — soft enough to conform to micro-texture on smooth hard floors, firm enough to support furniture weight without excessive compression. The heavier the furniture, the stronger the grip. NR+CR provides high static friction that increases under load rather than decreasing. The Shore A durometer scale measures rubber hardness — 30A sits in the range between soft grip compounds and structural rubber, the ideal balance for floor-contact applications.
Unlike silicone pads that harden and lose traction with age, NR+CR maintains consistent grip properties across a wide temperature range. Resistant to ozone, UV, and common household chemicals. Does not stain, discolor, or leave marks on finished floors.
The rivet’s razor-sharp tubular edge separates wood fibers rather than removing them. The entry hole closes back when the rivet is removed — unlike a plain nail hole, which widens with every movement and replacement.
On anti-slip glides, the mechanical rivet is especially important. The NR+CR rubber surface generates resistance forces that pull against the mounting — every lateral force on the furniture translates into tension on the glide-to-leg connection. A mechanical rivet absorbs those forces without compromising the bond. The strongest possible connection between glide and furniture.
The rigid platform that carries both the NR+CR rubber surface and the rivet. ABS distributes the furniture’s weight evenly across the full rubber contact surface — maximizing grip. Without the rigid platform, the rubber would compress unevenly under point loads, reducing the effective contact area and grip strength.
Cheap stick-on rubber pads and silicone dots use thin material on a weak adhesive backing. The adhesive peels off the leg under the lateral forces that anti-slip glides are specifically designed to resist — the harder the rubber grips the floor, the harder it pulls against the mounting. Within weeks, cheap rubber pads end up on the floor instead of the furniture leg.
Round anti-slip nail-on furniture glides for hard floors use 30 Shore A NR+CR rubber on a rigid ABS platform, mechanically riveted into solid wood. The rivet cannot peel. The platform distributes load evenly. The rubber surface is thick enough to conform to floor micro-texture for maximum grip — not a thin film that provides minimal friction.
Rubber leg caps slide over the end of the leg and rely on friction fit to stay in place. On smooth, finished wood, that friction fit loosens quickly — temperature changes, humidity cycles, and daily use all contribute to gradual slippage. A rubber cap that falls off a furniture leg in a commercial environment is both a liability and a maintenance headache.
Round anti-slip nail-on furniture glides are mechanically locked to the leg. They cannot slip off, fall off, or loosen over time. The NR+CR rubber surface provides superior grip compared to commodity rubber caps, and the rigid ABS platform prevents the uneven compression that causes rubber caps to rock and tilt under load.
Standard PA6 round nail-on furniture glides are designed for low friction — they help furniture slide smoothly. If the furniture is drifting, creeping, or migrating on smooth floors and you want it to stop, PA6 glides will not solve the problem. They are engineered to do the opposite.
Round anti-slip nail-on furniture glides for hard floors use NR+CR rubber instead of PA6 — a high-friction surface instead of a low-friction surface. Same ABS platform. Same ZnFe rivet. Opposite result. View standard PA6 round nail-on furniture glides →
Round self-adhesive furniture pads use a PA6 needle-punched surface — designed to slide, not grip. They are available in 33 diameters from Ø 12 mm to Ø 300 mm and are an excellent choice for furniture that should move freely on smooth hard floors. If you need anti-slip grip, pads are not the right product — use these round anti-slip nail-on furniture glides or round anti-slip self-adhesive furniture glides instead.
For furniture that doesn’t need anti-slip but does need floor protection in a size not available in the glide range, pads provide the widest size selection with the same PA6 surface quality.
Round nail-on furniture glides come in two surface variants. The right choice depends on how the furniture is used — not the floor type.
For furniture that is regularly repositioned. The low-friction PA6 surface moves quietly across hardwood, tile, laminate, vinyl, and stone with minimal effort. The standard choice for dining chairs, desk seating, and accent furniture where ease of movement is the priority.
NR+CR rubber at 30 Shore A provides controlled grip. Furniture stays exactly where it’s placed. The right choice for accent furniture, display pieces, restaurant tables, boat cabin furniture, RV seating, and any environment where an unexpected slide is a safety hazard.
Both variants use the same ABS platform and ZnFe tubular rivet. Only the surface material differs — PA6 for low friction, NR+CR for high friction.
Anti-slip nail-on furniture glide shape must match the leg cross-section exactly. On anti-slip glides, shape match matters even more than on standard PA6 — every square millimeter of rubber-to-floor contact area contributes to grip strength. Measure the base before ordering.
For circular cross-section legs — turned, tapered, and cylindrical. Ø 23 / 28 / 38 / 50 / 75 mm.
For equal-sided square legs. Full corner-to-corner grip — a round glide on a square leg loses rubber contact at all four corners.
For oblong legs with unequal sides — mid-century modern and Scandinavian furniture design. 33 × 19 mm.
Accent chairs, side tables, sofa end tables, bookcases, display cabinets, TV stands, and any round-legged wooden furniture that should stay in position on smooth hard floors. Also ideal for furniture near stairs, on raised platforms, or in homes with children and pets where stability is a safety concern. The Ø 28 mm and Ø 38 mm sizes cover the majority of residential accent furniture with round legs.
Restaurant tables, hotel lobby furniture, healthcare waiting room seating, assisted living facility furniture, retail display fixtures, boat cabin furniture, and RV built-ins. Round anti-slip nail-on furniture glides for hard floors are the preferred choice in commercial environments where unexpected furniture movement creates a liability — mechanical riveting provides the strongest connection, and the NR+CR rubber maintains grip under the dynamic forces of high-traffic settings and moving vessels. Available in bulk quantities for fit-outs and large-scale installations.
Identical ABS platform and ZnFe rivet. PA6 low-friction sliding surface instead of NR+CR rubber — for round-legged wooden furniture that should glide freely on smooth hard floors.
Same NR+CR rubber surface. EHBF adhesive backing instead of rivet — for metal, plastic, or hollow round furniture legs that can’t accept a nail-on fitting.
| Specification | Details |
|---|---|
Product Type |
Round Anti-Slip Nail-On Furniture Glides |
Shape |
Round |
Materials |
NR+CR rubber surface, ABS base plate, ZnFe steel tubular rivet |
Shore Hardness |
30 Shore A |
Fit Style |
Nail-on tubular rivet — no pre-drilling required |
Leg Compatibility |
Solid wooden furniture legs only |
Floor Compatibility |
All hard floors — hardwood, laminate, vinyl, tile, stone, concrete, marine flooring |
Furniture Compatibility |
Chairs, stools, tables, boat & yacht cabin furniture, RV furniture, and other solid wood-leg furniture |
Sizes Available |
Ø 23 mm – Ø 75 mm (0.91″ – 2.95″) |
Color Options |
Black |
Installation Type |
Tap in with hammer or rubber mallet |
Indoor/Outdoor Use |
Indoor | Covered Outdoor |
| Shape | Ø (Diameter) | Compatible Leg/Base Size | Ø1 (Rivet Diameter) | H (Height) | H1 (Rivet Height) |
|---|---|---|---|---|---|
Round |
23 mm (0.91″) |
23 – 27 mm (0.91 – 1.06″) |
9.2 mm (0.36″) |
12 mm (0.47") |
5.5 mm (0.22″) |
Round |
28 mm (1.10") |
28 – 37 mm (1.10 – 1.46″) |
9.2 mm (0.36″) |
12 mm (0.47") |
5.5 mm (0.22″) |
Round |
38 mm (1.50") |
38 – 49 mm (1.50 – 1.93″) |
9.2 mm (0.36″) |
12 mm (0.47") |
5.5 mm (0.22″) |
Round |
50 mm (1.97") |
50 – 74 mm (1.97 – 2.91″) |
9.2 mm (0.36″) |
12 mm (0.47") |
5.5 mm (0.22″) |
Round |
75 mm (2.95") |
75 mm + (2.95″) |
9.2 mm (0.36″) |
12 mm (0.47") |
5.5 mm (0.22″) |
Only logged in customers who have purchased this product may leave a review.
Reviews
There are no reviews yet